Select your vehicle
Refine by:

1993 Ford Bronco Clutch Pedal Pad

Showing 1 - 1 of 1 results
Sort by:
Clutch Pedal Pad
Dorman®
Part Number: RB20729
Guaranteed to Fit
$12.23
Vehicle Fitment
  • 1993 Ford Bronco Custom All Engines Standard Transmission
  • 1993 Ford Bronco XLT Lariat All Engines Standard Transmission
  • 1993 Ford Bronco Eddie Bauer All Engines Standard Transmission
  • 1993 Ford Bronco XL All Engines Standard Transmission
Product Details
Notes : Push On AttachmentProp 65 Warning :

Warning SymbolWARNING: This product can expose you to chemicals including Acrylonitrile, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Page 1 of 1 | Showing 1 - 1 of 1 results

1993 Ford Bronco Clutch Pedal Pad Customer Reviews

Clutch Pedal Pad
Jul 03, 2019
Good Quality/Easy Install
This pedal pad is made of good quality rubber and very easy to install! Took only a few minutes.
Purchased on Nov 30, 2016

Helpful Automotive Resources

P0715 Code: Input/Turbine Speed Sensor “A” Circuit
September 16, 2020
P0715 Code: Input/Turbine Speed Sensor “A” CircuitDiagnostic Trouble Code (DTC) P0715 stands for Input/Turbine Speed Sensor “A” Circuit. To put it simply, this code is triggered when your vehicle’s PCM detects an irregularity in the signal sent by the input speed sensor in the transmission.
P0445 Code: Evaporative Emission System Purge Control Valve “A” Circuit Shorted
September 16, 2020
P0445 Code: Evaporative Emission System Purge Control Valve “A” Circuit ShortedAs was mentioned, the EVAP system stores fuel vapors in a charcoal canister. When conditions are correct, Your car’s primary computer, which is often referred to as the powertrain control module (PCM), opens a device called the purge valve. Opening the valve creates a vacuum that draws fuel vapors from
P0022 Code: Intake “A” Camshaft Position – Timing Over-Retarded (Bank 2)
September 16, 2020
P0022 Code: Intake “A” Camshaft Position – Timing Over-Retarded (Bank 2)Diagnostic trouble code (DTC) P022 code stands for “Intake “A” Camshaft Position – Timing Over-Retarded (Bank 2).” It indicates that your car’s primary computer, which is often referred to as the powertrain control module (PCM), perceives an over-retarded or over delayed timing condition in Bank 2 of the intake camshaft. Code
P0307 Code: Cylinder #7 Misfire Detected
September 16, 2020
P0307 Code: Cylinder #7 Misfire DetectedDiagnostic trouble code (DTC) P0307 stands for “Cylinder #7 Misfire Detected.” This code is logged when the powertrain control module (PCM) perceives that your vehicle’s cylinder #7 may be misfiring. This indicates that incomplete combustion is happening inside the cylinder.
P2006 Code: Intake Manifold Runner Control Stuck Closed (Bank 1)
September 16, 2020
P2006 Code: Intake Manifold Runner Control Stuck Closed (Bank 1)Diagnostic trouble code (DTC) P2006 stands for “Intake Manifold Runner Control Stuck Closed (Bank 1).” It is logged when the powertrain control module or PCM directs the IMRC to open, but detects that the IMRC actuator for engine bank 1 is stuck in the closed position.
Longer Ford Escape Rumored to Be Under Development
September 15, 2020
Longer Ford Escape Rumored to Be Under DevelopmentThe model has the temporary name of CX430 and is planned to ride the same C2 platform that underpins the standard Escape, as well as the new Bronco Sport. With the longer wheelbase, the model is also expected to have a few design changes, especially with the roof.
Copyright ©2020 CarParts.com, Inc. All Rights Reserved.
Terms of Use
Privacy Policy