Need Assistance? Live Chat
Need Assistance? (Se Habla Espanol) Call 1-877-702-1308 or Chat Online

Select by Category

Select by Brand

Get Email Exclusives

Sign up for email updates on the latest exclusive offers

Dodge Ramcharger Turn Signal Switch

Causes behind a Faulty Dodge Ramcharger Turn Signal Switch

The turn signals equipped on your Dodge Ramcharger are an important safety feature of your vehicle. These lights signal other drivers of your next move in order to avoid a collision. Without a fully functional turn signal switch, these parts will not be able to light up properly. In fact, you may even encounter them to flash rapidly or slowly. So, if you find that the turn signals are already exhibiting unusual changes, then better prepare your gear and perform some troubleshooting. Here are a few common problems behind a faulty Dodge Ramcharger turn signal switch and the reasons behind them.

Only one turn signal does not light

If only one of the turn signals do not light, then the most probable culprit is a burnt out bulb. You can easily check for one by replacing the bulb. If a replacement works, then the stock bulb has just exceeded its service life. Most of the times, the bulbs have broken filaments, which then causes lighting failure. In other cases, corrosion in the sockets can impede the flow of electricity. If this is not the case, then check for dirty contacts or inspect for a poorly seated ground.

Both turn signals on one side do not work

When both turn signals on one side suddenly stop working, the first thing you should check for is bad bulbs. But if everything on the bulbs seems to look fine, then inspect the sockets and housings. This kind of turn signal defect usually indicates a bad ground on both housings.

Turns signals fail to flash

To check for a flasher failure, first push the turn signal switch in either direction. Afterwards, check if the light on the dash blinks or just stays lit up. If the latter is the case, then you might need to find new flashers for the turn signals.

Rapid or slow turn signal flashing

A too fast or too slow turn signal flashing usually indicates incompatible bulb equipment. Check if a heavy-duty bulb is installed instead of a regular one or vice versa. If this is still not the case, then you probably have loose connections or corroding bulb sockets.

Dodge Ramcharger Turn Signal Switch Bestsellers View more

Dodge Ramcharger Turn Signal Switch Available Years

  • Tips to Keep a Dodge Ramcharger Turn Signal Switch in Top Condition 27 February 2013

    Turn signals are automotive lights that provide a safety feature for your Dodge Ramcharger. In fact, equipping your car with efficient turn signal lights can help other drivers avoid hitting your vehicle. This is because the lights tell what direction your car is heading. These lights are triggered via a turn signal switch through a lever installed in your car's steering wheel. If you want to keep this part in top shape, then you must know how to perform maintenance on the whole turn signal assembly. So, if you are quite unsure on how to go about maintenance, here are a few tips and tricks to keep a Dodge Ramcharger turn signal switch in top condition:


    Regularly inspect the turn signal sockets.


    As preventive maintenance, habitually check the turn signal sockets for any signs of corrosion. You should look for unusual marks such as, burn marks, discoloration, and wear and tear. If you have seen signs of burn marks, it is advised that you use an Ohm meter to test for circuit voltage. In addition, you can wipe away the mentioned wear marks by using sand paper.


    Clean the turn signal sockets with electrical contact cleaner.


    Dirt and grime found on the turn signal sockets can easily be wiped off with an electrical contact cleaner. Luckily, if you do not have this cleaning tool, you may use white vinegar instead. Simply spray the solution on the sockets and allow it to settle for around 10 minutes. Afterwards, wipe off the dirt and grime with a rag. If you still find signs of stains, then you may use a steel wool to buff the sockets.


    Apply lubricant to prevent corrosion.


    To keep the turn signal switch working with the rest of the turn signal assembly, it is ideal that you help prevent corrosion on the sockets. You can do so by applying a coat of lubricant to the contacts. Be careful during application because the sockets have sharp edges.


    Solder loose wires.


    Over time, the wires on the assembly can get loose and cause the turn signals to malfunction. Luckily, they can easily be addressed by simply soldering them back into place.