Need car parts? Select your vehicle
Reading Time: 2 minutes

Watch this video to learn how to replace the rear ABS sensor on a 2009-2018 Dodge RAM 1500.

Replacing Rear ABS Sensor on a 2009-2018 Dodge RAM 1500: What You Need

Ready to perform this DIY replacement job? Remember that all the parts in this guide can be found on CarParts.com. Check out all the products that fit your vehicle right here.

Parts Checklist

Tightening Torques

  • No tightening torques for this operation

Tools Checklist

Here’s the toolbox we recommend to repair your Dodge RAM 1500: HM85 85 Piece Ratchet and Socket Set

List of tools:

Step-by-Step Instructions

Step 1: Turn off your engine and set the parking brake.

Step 2: Loosen the rear wheel’s lug nuts.

Step 3: Lift the front of your vehicle using a suitable jack. Refer to the video on “How to jack your RAM 1500 safely” for guidance.

Step 5: In order to change the rear ABS sensor, take off the wheel to have full access.

Step 6: Don’t forget to put the wheels under the vehicle.

Step 7: Using a ratchet and an 8 mm socket, unscrew the ABS sensor’s retaining bolt.

Step 8: Finish unscrewing the cap by hand.

Step 9: Then, remove the sensor by jiggling it back and forth.

Step 10: Unclip all the retaining clips holding the ABS sensor cable onto the brake hose.

Step 11: Using a fork, unclip the ABS sensor cable retaining clip located on the chassis.

Step 12: Once the cable is completely unclipped, remove the ABS sensor cable connector from its support.

Step 13: Disconnect the connector by pressing on the plastic tab using a flat-head screwdriver and pulling on the connector.

Step 14: Remove the cable.

Step 15: Take the new cable.

Step 16: Slide it into its housing.

Step 17: Reconnect the connector. Then lock it.

Step 18: Reclip the connector onto its support.

Step 19: Reclip the cable back onto the support.

Step 20: Reclip all of the ABS sensor cable retaining clips.

Step 21: Before installing the new sensor, thoroughly clean its location using a wire brush.

Step 22: Insert the sensor into its housing.

Step 23: Retighten the retaining bolt.

Step 24: Put the wheel back on your vehicle.

Step 25: Lower the car to the ground and block the wheel properly.

Step 26: The operation is now complete.

Compatible Vehicles

The operation and tools displayed in the video should be available on the following vehicles:

Important Reminders

  • Before installing the new sensor, we recommend that you thoroughly clean its location using fine sandpaper.

Disclaimer:

This video is for entertainment purposes only. CarParts.com, Inc. disclaims all damages including, but not limited to, actual, consequential, and/or punitive, for any liability, claim, or any other injury or cause related to or arising from any information or lack thereof posted in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All mechanical car projects entail some risk. It is the sole responsibility of the viewer to assume this risk. If you are in doubt, please consult a licensed mechanic in your area.

About The Author
Reviewed By carpartspromotions

In the Garage with CarParts.com is an online blog dedicated to bringing DIYers and devoted car enthusiasts up to date with topical automotive news and lifestyle content. Our writers live and breathe automotive, taking the guess work out of car repairs with how-to content that helps owners get back on the road and keep driving.

Any information provided on this Website is for informational purposes only and is not intended to replace consultation with a professional mechanic. The accuracy and timeliness of the information may change from the time of publication.

File Under : Ram 1500 2009-2018
get 10% off everything
Subscribe
Notify of
guest
0 Comments
Inline Feedbacks
View all comments

View all Questions & Answers

expand_more
CarParts.com Answers BE PART OF OUR COMMUNITY: Share your knowledge & help fellow drivers Join Now
Copyright ©2023 CarParts.com, Inc. All Rights Reserved.