Things to Consider When Buying a New A/C Condenser Fan
Driving with a faulty component in your A/C system is going to be a real drag. It will not only result to a very uncomfortable ride, but it will also make you vulnerable to getting sick if the glitch is prolonged. That's why, it's very important that you check your car's A/C parts regularly such as the A/C condenser fan. This fan is actually a part of the A/C condenser, a radiator-like device that dissipates heat that comes from your engine. The condenser basically cools the air with the use of this fan, so if this becomes defective, the entire A/C system operation will sure be affected. In case your A/C condenser fan is malfunctioning, you'd better address it right away to prevent the problem from getting out of hand. A faulty fan can cause mechanical wear in your vehicle components and make your ride stall. And if worse comes to worst, your car may not even run at all. To prevent this from happening, put your money on a new component right away.
Single fan or dual fan?
When looking for a replacement A/C condenser fan, you need to decide whether to get a single fan or dual-fan. Most vehicle types use the single-fan assembly. However in some SUVs, double A/C units are used, so the dual-fan type is recommended. Be sure to check your vehicle specs before buying to ensure you get only the right part.
Sold individually or entire assembly?
Depending on what you need for your vehicle repairs, A/C condenser fans are typically sold in two ways: individually or as a complete assembly. More often than not, getting an entire assembly is more ideal because it comes with almost everything that you'll need for your repairs. This will also save you some cash as well as time and money because you won't have to spend a lot in buying tools separately.
FINAL TIP: To make sure you get your money's value, never be satisfied with cheap yet poor-quality products. Always buy from a brand that you can trust to ensure you get the best for your ride. For your needed A/C condenser fan, consider reliable names like Four-Seasons, Auto Trust, Dorman, and Replacement.
Changing Your Car's A/C Condenser Fan
Addressing a faulty or malfunctioning A/C condenser fan is definitely a must because if the problem persists and gets out of hand, it can affect the overall performance of your ride. In fact, it cause mechanical wear and make your engine stall or idle badly. It can also bring you great discomfort every time you are out on the road because your A/C will not be able to regulate your cabin temperatures properly. To get your vehicle's A/C back on track, the best thing you can do is address it right away. Below are a few basic steps that you can follow to get stared with your repairs.
Difficulty Level: Moderate
What You'll Need:
- Metric wrench set
- Socket and ratchet with extension (size depends on your vehicle)
- Flat blade screwdriver
- Philips screwdriver
- Replacement A/C condenser fan
Step 1: To get started, use your wrenches to disconnect the negative and positive cables of your battery. Remove the bolt that holds the battery in place and disconnect the other cables attached to it. Take your battery out with caution and put it in a safe place.
Step 2: Remove your fuse relay by unbolting it and sliding it towards the engine until it pops out of place.
Step 3: Remove your A/C fan, radiator, fan shroud, and A/C line by unbolting them by using a regular screwdriver to remove the pins. Once the radiator is detached, move it backwards to gain access to your A/C condenser fan.
Step 4: Detach the condenser fan from your assembly by removing the four bolts that secure it in place. Remove it very carefully to avoid damaging other components under your hood.
Step 5: Take your new A/C condenser fan and attach it to your fan assembly. Remember to keep an eye on all the wiring components that you might hit while installing the fan. To check its position, see that it that your fan shroud is underneath the condenser.
Step 6: Once it's in position, secure it in place by bolting it up. Start reattaching fan shroud.
Step 7: Slide your battery box back in place and secure it by using pins. Put the battery back and secure its position by bolting it and tightening it up slowly. Reconnect the positive cable of the battery, the ground strap of the fender, and the negative battery cable.