Select your vehicle
Refine by:

Window Regulator Clip

Showing 1 - 1 of 1 results
Sort by:
GenuineXL 163-988-05-78 Window Regulator Clip - Replaces OE Number 163-988-05-78
Vehicle Info Required to Guarantee Fit
$6.78
Vehicle Fitment
  • 1998 - 2003 Mercedes Benz ML320 All Submodels All Engines
  • 1999 - 2001 Mercedes Benz ML430 All Submodels All Engines
  • 2000 - 2003 Mercedes Benz ML55 AMG All Submodels All Engines
  • 2002 - 2005 Mercedes Benz ML500 All Submodels All Engines
  • 2003 - 2005 Mercedes Benz ML350 All Submodels All Engines
Product Details
Location : Rear, Driver Or Passenger SideWarranty : 24-month limited warrantyAnticipated Ship Out Time : Same day - 1 business dayQuantity Sold : Sold individually
Page 1 of 1 | Showing 1 - 1 of 1 results

Window Regulator Clip Guides

Finding Compatible Window Regulator Clips for Your Car

Rolling your window up and down can take a toll on a lot of parts. Everything from the window's handles or buttons up to its internal mechanisms can wear out due to repeated use. One of the items that you'll need to check out would be the window regulator clips. These small items basically hold your window in place as you roll it up and down. These clips could break due to wear and tear and will need to be replaced ASAP, or you won't be able to open or close your windows properly. It isn't hard to get a compatible window regulator clip, and they're pretty much basic components that most online car parts stores have plenty of stock of.

Choosing between old or new designs

There are actually two common designs when it comes to window regulator clips. The older designs are typically made up of two parts; a metal clamp that attaches to the bottom of the window glass and a plastic support that slides up and down the window regulator track whenever you open or close your car's windows. Newer clips are made from a single piece of metal with a small plastic sleeve that allows it to slide up and down the window regulator. This newer design is stronger since it's made from a single piece, which wouldn't snap so easily.

Go for an OEM replacement

The easiest way to determine what kind of window car regulator clip your car uses is to check your vehicle's manual. If you can't find any information from there, then you might need to call your dealer or simply disassemble your doors trim panel to take a look at the window regulator clip. More importantly, you should always get a replacement that's made specifically for your vehicle. OEM replacements are perfect for this since they're made according to the exact specifications of a particular vehicle make and model. Prices for a basic window regulator clip can go as low as $5 to as high as $20, and you shouldn't have to pay any more than that.

Replacing Your Window Regulator Clip

Your car's windows may well last forever but the clips that hold them in place will not. The stress and strain of repeated use of your vehicle's windows can damage the window regulator clip. This small part can break or crack even under normal circumstances. Lucky for you, this small part is quite easy to replace. Most people can probably replace this clip in under an hour with just a couple of basic tools. You won't need to waste money by hiring a mechanic or visiting a repair shop. Simply follow our short guide and you'll be able to replace it like a pro!

Difficulty level: Moderate

What you'll need

  • Screwdriver
  • Trim tool
  • Wrench
  • Duct tape

Step 1: You'll need to remove the trim panel of your car's door so you could access your window regulator clip. Most trim panels simply snap in place so you could easily pry it loose using a small flat screwdriver or a trim tool. Be careful when prying the panel loose so that you avoid damaging it or other nearby components.

Step 2: You won't be able to completely remove your panel without disconnecting a couple of wires. Unplug all the wires and cables while taking note of where they connect to so that you can install them properly later on.

Step 3: On some vehicles, you'll need to peel the plastic water shield away from the door so you can see your window clips clearly.

Step 4: Locate your window regulator by removing a couple of grommets and a rubber cover that holds it in place.

Step 5: You'll need someone to hold the window in place while you take out the clips so that it won't fall down once the clips are removed. Alternatively, you could use duct tape to temporarily hold it in place while you remove the regulator clip.

Step 6: On some vehicles, it'll be better to remove the glass window entirely. Remember to set aside the window in a safe place.

Step 7: Loosen the bolts or screws that hold the window regulator clip in place. You'll be able to remove the clips and simply replace them with new ones. Tighten the bolts into place to create a snug fit.

Step 8: From here, you'll simply have to reinstall everything in reverse. Take particular care in reconnecting the wires in your door panel and make sure that they're all connected properly before you snap the panel back into place.

Step 9: Test your window to make sure that it's functioning correctly and you're done!

Visit Our Blog
Follow Us
Shop With Confidence
Copyright ©2020 Carparts.com. All Rights Reserved.
Terms of UsePrivacy Policy