Select your vehicle
Refine by:

1963 Ford Galaxie 500 Brake Drum

Showing 1 - 2 of 2 results
Sort by:
Brake Drum Front
Centric®
Part Number: CE123.61003
Guaranteed to Fit
$46.08
Vehicle Fitment
  • 1963 Ford Galaxie 500 All Submodels All Engines Except Taxi & Heavy Duty
Product Details
Location : FrontNotes : 3.66 in. height; 11 in. nom. diameter; 1.09 in. max. diameter; 2.84 in. friction surface; 2.43 in. hub reg.; 0.61 in. bolt sizeBolt Pattern : 5 x 4.5 in. Bolt PatternDiameter : 12.8 in. DiameterQuantity Sold : Sold individuallyWarranty : 90-day or 3,000-mile Centric limited warranty
Brake Drum Front
Centric®
Part Number: CE122.61003
Guaranteed to Fit
$50.35
Vehicle Fitment
  • 1963 Ford Galaxie 500 All Submodels All Engines Except Taxi & Heavy Duty
Product Details
Location : FrontDiameter : 12.8 in. DiameterQuantity Sold : Sold individuallyWarranty : 90-day or 3,000-mile Centric limited warranty
Page 1 of 1 | Showing 1 - 2 of 2 results

Helpful Automotive Resources

P0715 Code: Input/Turbine Speed Sensor “A” Circuit
September 16, 2020
P0715 Code: Input/Turbine Speed Sensor “A” CircuitError code P0715 is a generic trouble code, so it is supported in various makes and models. However, keep in mind that the repair and diagnostic procedures for each may vary depending on the specific vehicle you own.
P0445 Code: Evaporative Emission System Purge Control Valve “A” Circuit Shorted
September 16, 2020
P0445 Code: Evaporative Emission System Purge Control Valve “A” Circuit ShortedThe PCM performs various tests on the EVAP system. If the module perceives a problem with the purge valve or its circuit, it turns on the check engine light and stores code P0445 in its memory.
P0022 Code: Intake “A” Camshaft Position – Timing Over-Retarded (Bank 2)
September 16, 2020
P0022 Code: Intake “A” Camshaft Position – Timing Over-Retarded (Bank 2)The crankshaft and camshaft position sensors relay information to the PCM. The module uses the data to determine whether the engine is timed properly by comparing the input from both sensors. As was mentioned, in newer vehicles, a variable valve timing system orchestrates the opening and closing of the intake
P0307 Code: Cylinder #7 Misfire Detected
September 16, 2020
P0307 Code: Cylinder #7 Misfire DetectedRemember that the efficient burning of air and fuel is essential to engine operation. Without the proper combustion of the air/fuel mixture, the engine won’t run properly or won’t run at all.
P2006 Code: Intake Manifold Runner Control Stuck Closed (Bank 1)
September 16, 2020
P2006 Code: Intake Manifold Runner Control Stuck Closed (Bank 1)The PCM controls the operation of the intake manifold runner control (IMRC) system. It is made up of butterfly-shaped flaps that fit into the intake manifold runner. An electronic runner control solenoid opens and closes these flaps in order to fine tune air flow to the intake manifold.
Longer Ford Escape Rumored to Be Under Development
September 15, 2020
Longer Ford Escape Rumored to Be Under DevelopmentThe third row of this new Escape will be accessible from the second row. But aside from this addition, there will likely be no other major enhancements in the cabin. The future Escape will also sport the same powertrains as the newly released generation. Ford is expected to release it
Copyright ©2020 CarParts.com, Inc. All Rights Reserved.
Terms of Use
Privacy Policy