Essential Maintenance Points to Follow for the Chevrolet C1500 Bumper
The bumper of your Chevrolet C1500 has the dual role of completing the truck's look as well as helping absorb the impact of a collision, so it is only right that this component is maintained well. Although they are made of durable plastic, the bumper is still vulnerable to damaging elements and will quickly succumb to wear without proper care and maintenance. Keeping your truck's bumper in top shape is not that difficult and will only require an hour or two of your time to accomplish. Here are some simple ways to maintain the Chevrolet C1500 bumper:
Dirt and grime can quickly build up on the surface of the bumper, but this can effectively be removed by thorough hand washing. Although it does take more time and effort compared to bringing your truck to an automatic car wash, washing the bumpers by hand results in more detailed cleaning, particularly in hard-to-reach areas. In addition, drive-in car washes often use brushes with hard bristles that can scratch on the bumper surface.
Ideally, you should wash the bumper with a wash mitt using a solution of car shampoo and warm water. Do not use dishwashing soap, as it contains harsh chemicals that can strip wax and polish off the bumper surface. It is also recommended to wash the bumper under a shaded area to prevent the shampoo from drying up too quickly and leaving spots.
While washing the bumpers is enough to remove dirt and other contaminants, it should always be followed up with a coating of car wax. Aside from giving the bumpers a luxurious sheen, car wax also serves as a protective layer that repels dirt and moisture as well as minimizes the effect of scrapes and scuffs on the surface of the bumper.
- Fix minor scratches with rubbing compound.
We all make mistakes when driving, but that can be hard to forget if it leaves a scratch on the bumper. If the scratch did not penetrate through the paint, you might still be able to fix it using a rubbing compound. Simply apply the compound onto the damaged surface and buff by hand or by an orbital sander depending on the product's instructions.
Four Handy Tips for Installing a New Chevrolet C1500 Bumper
Whether you are replacing a dented fender or upgrading to a custom-made one, installing a new bumper on your Chevrolet C1500 can certainly breathe new life to the appearance of your truck. While you can have your new bumper installed in auto body shops, they can be easy enough to install on your own. Installing a new Chevrolet C1500 bumper can be a rewarding and money-saving experience as long as you have the skills and the equipment on hand. Below are some tips that can be helpful during the process:
Tip #1: Disconnect power from the battery.
Removing the old bumper also entails removing the fog lights or even the headlights if necessary, so it is recommended to remove the battery cables from the battery terminals first to prevent electric shock during the installation process. Make sure that the engine is switched off and wear protective gloves before handling the battery.
Tip#2: Check the new bumper for imperfections.
Bumpers are usually shipped with a black, pre-primed coat with bumps, rough spots, and other imperfections. Wash the bumper clean with car shampoo and warm water to remove dust and grease, and wet-sand the surface with 600-grit sandpaper to remove any irregularities. Do not use a sander, as it may take away too much of the surface material.
Tip #3: Use an auto body clip puller to removing the retaining clips.
Some bumpers are secured in place by plastic retaining clips. These clips can usually be pried off with a knife or a flathead screwdriver, but this can also damage both the clips and their mounting points. You can use an auto body clip puller, instead. Often stocked in auto parts and hardware stores, these pullers can pull retaining clips off the bumper without damaging them. They can also work with the retaining clips found in the car doors and other body panels, making this tool a worthwhile investment to make.
Tip #4: Don't forget to pre-fit.
Replacement bumpers, custom aftermarket ones in particular, may require a bit of modification in order to achieve perfect fit, so pre-fitting is definitely required. With two people holding up both ends, lift the bumper up to its mounting points. Check if the holes for the screws and retaining clips line up properly and if the panel sits flush to the rest of the truck.