Select your vehicle
Refine by:

Shop Audi S8 Mass Air Flow Sensor

Showing 1 - 6 of 6 results
Sort by:
Mass Air Flow Sensor
Replacement
Part Number: RA31670002
Vehicle Info Required to Guarantee Fit
$21.50
Vehicle Fitment
  • 2007 - 2009 Audi S8 Base 10 Cyl 5.2L
Product Details
Notes : With housingReplaces OE Number : 07C906461AQuantity Sold : Sold individuallyWarranty : 1-year Replacement unlimited-mileage warrantyProp 65 Warning :

Warning SymbolWARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Mass Air Flow Sensor
Walker Products®
Part Number: WKP2451222
Vehicle Info Required to Guarantee Fit
$98.12
Vehicle Fitment
  • 2001 - 2003 Audi S8 Base 8 Cyl 4.2L
Product Details
Notes : Full assembly with housingReplaces OE Number : 077133471K, 077133471KXQuantity Sold : Sold individuallyWarranty : 90-day Walker limited warranty
Mass Air Flow Sensor
Walker Products®
Part Number: WKP2452222
Vehicle Info Required to Guarantee Fit
$79.71
Vehicle Fitment
  • 2001 - 2003 Audi S8 Base 8 Cyl 4.2L
Product Details
Notes : Sensor onlyQuantity Sold : Sold individuallyWarranty : 90-day Walker limited warranty
Mass Air Flow Sensor
A1 Cardone®
Part Number: A17410120
Vehicle Info Required to Guarantee Fit
$92.56
+$23.91
  Core Charge
Vehicle Fitment
  • 2001 - 2003 Audi S8 Base 8 Cyl 4.2L
Product Details
Notes : Plastic Housing Material; Bolt-On Mounting TypeQuantity Sold : Sold individuallyWarranty : 1-year or 18,000-mile A1 Cardone limited warranty
Mass Air Flow Sensor
A1 Cardone®
Part Number: A17410156
Vehicle Info Required to Guarantee Fit
$140.75
+$70.03
  Core Charge
Vehicle Fitment
  • 2007 - 2009 Audi S8 Base 10 Cyl 5.2L
Product Details
Notes : Plastic Housing Material; Bolt-On Mounting TypeQuantity Sold : Sold individuallyWarranty : 1-year or 18,000-mile A1 Cardone limited warranty
Mass Air Flow Sensor
Bosch®
Part Number: BS0280218067
Vehicle Info Required to Guarantee Fit
$147.20
Vehicle Fitment
  • 2001 - 2003 Audi S8 Base 8 Cyl 4.2L
Product Details
Quantity Sold : Sold individuallyWarranty : Lifetime Bosch limited warranty
Page 1 of 1 | Showing 1 - 6 of 6 results

Helpful Automotive Resources

P0170 Code: Fuel Trim (Bank 1)
September 16, 2020
P0170 Code: Fuel Trim (Bank 1)Note: Code P0170 is a generic code defined by the Society of Automotive Engineers (SAE). The vehicle’s manufacturer may set a different definition for the code. If the computer cannot properly adjust the air-fuel mix, it will log the diagnostic trouble code P0170. What are the Possible Causes of the P0170 Code?
P0100 Code: Mass or Volume Air Flow “A” Circuit
September 16, 2020
P0100 Code: Mass or Volume Air Flow “A” CircuitThe MAF sensor is located in the intake air duct. It is tucked between the air filter and the engine intake manifold that measures the density and volume of the air intake. Some MAF sensors have an intake air temperature sensor, which delivers values that the PCM uses to ensure
P0103 Code: Mass or Volume Air Flow “A” Circuit High
September 15, 2020
P0103 Code: Mass or Volume Air Flow “A” Circuit HighThe PCM changes the voltage it applies to the wire in response to the change in the wire’s resistance. Note that the voltage level that gets sent back to the PCM is proportional to the air flowing through the sensor.
P2187 Code: System too Lean at Idle (Bank 1)
September 10, 2020
P2187 Code: System too Lean at Idle (Bank 1)In an internal combustion engine, the air-fuel mixture is controlled by the powertrain control module (PCM). The PCM uses a closed-loop air-fuel metering system and monitors the heated oxygen sensor signal voltage. It utilizes various data from the sensors in the car, such as the oxygen sensors, manifold absolute pressure
P2A00 Code: O2 Sensor Circuit Range / Performance (Bank 1, Sensor 1)
September 09, 2020
P2A00 Code: O2 Sensor Circuit Range / Performance (Bank 1, Sensor 1)Diagnostic trouble code (DTC) P2A00 stands for “O2 Sensor Circuit Range/Performance (Bank 1, Sensor 1).” It is activated when the PCM detects an issue with the circuit range of the upstream O2 sensor on bank 1.
P2196 Code: O2 Sensor Signal Biased/Stuck Rich (Bank 1, Sensor 1)
September 03, 2020
P2196 Code: O2 Sensor Signal Biased/Stuck Rich (Bank 1, Sensor 1)The P2196 code indicates an issue in the oxygen sensor between the catalytic converter and the engine. Bank 1 refers to the side of the engine where the cylinder 1 is located. 
Copyright ©2020 CarParts.com, Inc. All Rights Reserved.
Terms of Use
Privacy Policy